| Table of contents |
Max Input Channels: 32 (single-ended), 24 (16/8 single-ended/differential), or 16 (differential)
A/D Resolution: 16 bits (1/65536 of full-scale)
Data range: -32768 to +32767 for all voltage ranges
Input Ranges (Bipolar): ±10V, ±5V, ±2.5V, ±1.25V, or ±0.625V
Input Ranges (Unipolar): 0-10V, 0-5V, 0-2.5V, or 0-1.25V
Supported Conversion Triggers: Software, Internal Clock, or External TTL Signal
Maximum Conversion Rate (Software Command): system-dependent, up to 100,000 per second
Maximum Conversion Rate (Interrupt Routine w/FIFO): 200,000 samples per second
FIFO: 512 samples with programmable threshold
This board supports the following programmable input ranges and resolutions:
| A/D Ranges | ||||||
|---|---|---|---|---|---|---|
| Code | Range | ADBU | G1 | G0 | Input Range | Resolution (1 LSB) |
| 0 | 0 | 0 | 0 | 0 | ±5V | 153μV |
| 1 | 0 | 0 | 0 | 1 | ±2.5V | 76μV |
| 2 | 0 | 0 | 1 | 0 | ±1.25V | 38μV |
| 3 | 0 | 0 | 1 | 1 | ±0.625V | 19μV |
| 4 | 0 | 1 | 0 | 0 | Invalid Setting | - |
| 5 | 0 | 1 | 0 | 1 | Invalid Setting | - |
| 6 | 0 | 1 | 1 | 0 | Invalid Setting | - |
| 7 | 0 | 1 | 1 | 1 | Invalid Setting | - |
| 8 | 1 | 0 | 0 | 0 | ±10V | 305μV |
| 9 | 1 | 0 | 0 | 1 | ±5V | 153μV |
| 10 | 1 | 0 | 1 | 0 | ±2.5V | 76μV |
| 11 | 1 | 0 | 1 | 1 | ±1.25V | 38μV |
| 12 | 1 | 1 | 0 | 0 | 0 - 10V | 153μV |
| 13 | 1 | 1 | 0 | 1 | 0 - 5V | 76μV |
| 14 | 1 | 1 | 1 | 0 | 0 - 2.5V | 38μV |
| 15 | 1 | 1 | 1 | 1 | 0 - 1.25V | 19μV |
NOTE: Ranges 9 through 11 are identical to ranges 0 through 2.
Max Output Channels: 4 D/A
Resolution: 12 bits (1/4096 of full-scale)
Data range: 0 to 4095 for all voltage ranges
Output Ranges (Bipolar): ±5V, ±10V, or programmable
Output Ranges (Unipolar): 0-5V, 0-10V, or programmable
Max Ports: 3 (bi-directional, programmable in 8-bit groups, TTL-compatible) similar to 82C55
Digital I/O ports on Diamond-MM-32-AT require direction to be set with dscDIOSetConfig() before use.
All DIO lines power-up in input mode and have readback capability.
All DIO lines have 4.7K Ohm pull resistors that can be configured for all pull-up or all pull-down with a jumper.
For these functions DMM32-AT has the following restrictions
dscADSampleInt, dscADScanInt
1. FIFO threshold (dscaioint.fifo_depth) must be a multiple of the number of channels
2. Num_conversions (dscaioint.num_conversions) must be a multiple of fifo threshold
3. FIFO threshold (dscaioint.fifo_depth) must be an even number between 0 to 510
This page was last modified 22:40, 7 Apr 2005.
Copyright (c) 2004 Diamond Systems. All Rights Reserved.